The door frame, commonly known as door pocket, is often used for fixing, corner protection, decoration, etc. of the door leaf to protect the door from scratch, corrosion, damage, dirt, etc. at present, with the improvement of people's requirements for quality of life, personal aesthetic needs have increased to a greater extent. How to design and make common door jambs

一、 不銹鋼門套做法

1、 Practice of stainless steel door pocket

01.不銹鋼門套有兩種樣式

01. there are two styles of stainless steel door pocket

一種是垂直與水平面成45度角的形式，另一種是垂直與水平面垂直安裝。建議采用后者。前者有時需要焊接和碰撞，非常麻煩，效果不好。常用的不銹鋼板分為201型和304型。事實上，成分是不同的。304的質量稍好一點，但價格較高。201有點差，大型商場或?qū)懽謽切枰?04不銹鋼來滿足需求。板的厚度也不同，一般0.6就足夠了。

One is vertical and horizontal at an angle of 45 degrees, and the other is vertical and horizontal. The latter is recommended. The former sometimes needs welding and collision, which is very troublesome and has poor effect. Commonly used stainless steel plates are divided into 201 and 304 types. In fact, the ingredients are different. The quality of 304 is a little better, but the price is higher. 201 a little poor. Large shopping malls or office buildings need 304 stainless steel to meet the demand. The thickness of the plate is also different, generally 0.6 is enough.

02. 不銹鋼門套的表面處理：板的表面處理也分為鏡面和油膜刷。一般來說，鏡面不銹鋼不推薦用于商業裝飾。油膜拉伸更好（即許多吸油煙機使用的材料）。

02. surface treatment of stainless steel door pocket: the surface treatment of the plate is also divided into mirror and oil film brush. Generally speaking, mirror stainless steel is not recommended for commercial decoration. The oil film is stretched better (i.e. the material used in many range hoods).

03.基本生產不銹鋼門套9%的木材可用作門套襯里。如果砌磚工人熟練，這一步可以省略，可以直接使用不銹鋼門框。

03. basically produce stainless steel door jambs. 9% of the wood can be used as door jamb lining. If the bricklayer is skilled, this step can be omitted and the stainless steel door frame can be directly used.

04.不銹鋼門套的測量：由于一般商業裝修數量較多，商家需要上門測量。此時測量需要小心準確，測量結果一定要準確到毫米。

04. measurement of stainless steel door pocket: due to the large number of general commercial decoration, businesses need to conduct door-to-door measurement. At this time, the measurement needs to be careful and accurate, and the measurement result must be accurate to mm.

05.不銹鋼門套加工選擇店內使用的折彎?rùn)C(jī)，確定款式，協商價格。人們會上門測量尺寸，而且處理速度非常快。

05. for stainless steel door pocket processing, select the bending machine used in the shop, determine the style and negotiate the price. People will come to the door to measure the size, and the processing speed is very fast.

二、 不銹鋼門套生產質量標準。

2、 Production quality standard for stainless steel door pocket.

1.所有黑鈦不銹鋼門框的落料一定準確，部件長度的允許偏差為1mm。

1. the blanking of all black titanium stainless steel door frames must be accurate, and the allowable deviation of component length is 1mm.

2.切割前要檢查不銹鋼門框是否平直，否則一定調直。

2. before cutting, check whether the stainless steel door frame is straight, otherwise it must be straightened.

3.焊接時，焊條或焊絲應與焊接材料相適應，不銹鋼門框的焊接材料品種應有出廠合格證。

3. during welding, the welding rod or welding wire shall be compatible with the welding material, and the type of welding material for stainless steel door frame shall have factory certificate.

4.焊接時，不銹鋼門框的位置一定正確。

4. when welding, the position of stainless steel door frame must be correct.

5.焊接時，不銹鋼門框之間的焊點應牢固、充足，焊縫表面焊縫應均勻。焊縫不得有咬邊、裂紋、裂紋、浮渣、焊塊、燒穿、電弧劃傷、弧坑和針狀氣孔，焊接區域不得飛濺。

5. during welding, the welding points between stainless steel door frames shall be firm and sufficient, and the welds on the weld surface shall be uniform. The weld shall be free of undercut, crack, crack, scum, welding block, burn through, arc scratch, arc crater and needle shaped air hole, and the welding area shall be free of spatter.

6.不銹鋼門框焊接后，應清除焊渣。

6. after the stainless steel door frame is welded, the welding slag shall be removed.

7.不銹鋼門框焊接組裝后，用手持式機器進行適當?shù)拇蚰ズ蛼伖猓蛊渫庥^光滑整齊。

7. after the stainless steel door frame is welded and assembled, it shall be properly polished and polished with a hand-held machine to make its appearance smooth and tidy.

8.用鍍鋅角鋼連接筒體

8. connect the cylinder with galvanized angle steel

9.與槽鋼、角鐵連接

9. connection with channel steel and angle iron

10.用自攻螺釘將9%鋼板與槽鋼連接

10. connect 9% steel plate and channel steel with tapping screws

本文的精彩內容由電梯不銹鋼門套提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://m.syhuaxi.cn我們有專門的客服為您解答問題

The wonderful content of this article is provided by the knowledge of elevator stainless steel door pocket. There are many wonderful content on this website. You can click to enter more content: http://m.syhuaxi.cn We have special customer service to answer your questions